60m Underwater Photography Video Fill-up Headlight Diving Flashlight with Battery Display Function(Headlight)
L'article est en stockDépêchez-vous ! Faible inventaireL'article est en rupture de stock
L'article n'est pas disponible
Product advantages:
1. Aluminum alloy solid lamp holder, enhance heat dissipation.
2.Hard oxidation, seawater corrosion resistance, scratch resistance.
3. The switch has its own power display function to understand the power status in real time.
Product parameter
Lamp beads model: 1xL2 lamp beads
Output brightness reaches 1000 lumens
Material: aviation-grade aluminum alloy (hard oxidation, seawater corrosion resistance, scratch resistance)
Lamp cup: smooth plating reflector cup
Power supply: 1*18650 lithium battery(not included)
Switch: middle button switch (with battery indicator)
Voltage higher than 3.4V, green light
Voltage 3.2-3.4V display yellow light
Voltage 3.0-3.2V shows red light
Voltage 2.8-3.0V red light flashes
Shut down when the voltage is lower than 2.8V;
Gear position: 3 gears (-50%-SOS)
Waterproof: IPX8 (diving depth of 60 meters)
Lamp size: length 88mm*width 72mm*37mm
Instructions for use
1. Check the battery: make sure that the battery is charged and the flashlight is installed in the correct direction;
2. When the headlight is in use, choose according to the voltage and battery requirements of the flashlight. Don''''t use it indiscriminately to prevent burnout of the circuit board. Don''''t use batteries of different models and voltages at the same time;
3. In use, when the brightness of the headlight changes significantly, turn off the headlight to prevent over-discharge of the battery, and charge it in time; pay attention to the waterproof, moisture-proof, and drop-proof of the battery, and charge according to the charging speed of the charger , After the indicator light changes, take it out in time, don''''t overcharge;
4. If the battery is not used for a long time, the battery should be fully charged and taken out for storage. Normally, it should be charged and discharged again in about three months to avoid chemical corrosion;
5. Keep the inner wall of the lamp cup clean. Do not wipe it with your hands or hard objects. To clear the fingerprints on the lens, you can wipe it gently with a cotton swab dipped in lens cleaner;
6. Do not keep the headlamp in contact with sunlight, water, chemicals and corrosive gases for a long time to avoid damage to the headlamp;
7. Non-professionals do not disassemble, to prevent damage to the circuit board structure.
8. Note: This product is shipped without batteries and chargers
1. Aluminum alloy solid lamp holder, enhance heat dissipation.
2.Hard oxidation, seawater corrosion resistance, scratch resistance.
3. The switch has its own power display function to understand the power status in real time.
Product parameter
Lamp beads model: 1xL2 lamp beads
Output brightness reaches 1000 lumens
Material: aviation-grade aluminum alloy (hard oxidation, seawater corrosion resistance, scratch resistance)
Lamp cup: smooth plating reflector cup
Power supply: 1*18650 lithium battery(not included)
Switch: middle button switch (with battery indicator)
Voltage higher than 3.4V, green light
Voltage 3.2-3.4V display yellow light
Voltage 3.0-3.2V shows red light
Voltage 2.8-3.0V red light flashes
Shut down when the voltage is lower than 2.8V;
Gear position: 3 gears (-50%-SOS)
Waterproof: IPX8 (diving depth of 60 meters)
Lamp size: length 88mm*width 72mm*37mm
Instructions for use
1. Check the battery: make sure that the battery is charged and the flashlight is installed in the correct direction;
2. When the headlight is in use, choose according to the voltage and battery requirements of the flashlight. Don''''t use it indiscriminately to prevent burnout of the circuit board. Don''''t use batteries of different models and voltages at the same time;
3. In use, when the brightness of the headlight changes significantly, turn off the headlight to prevent over-discharge of the battery, and charge it in time; pay attention to the waterproof, moisture-proof, and drop-proof of the battery, and charge according to the charging speed of the charger , After the indicator light changes, take it out in time, don''''t overcharge;
4. If the battery is not used for a long time, the battery should be fully charged and taken out for storage. Normally, it should be charged and discharged again in about three months to avoid chemical corrosion;
5. Keep the inner wall of the lamp cup clean. Do not wipe it with your hands or hard objects. To clear the fingerprints on the lens, you can wipe it gently with a cotton swab dipped in lens cleaner;
6. Do not keep the headlamp in contact with sunlight, water, chemicals and corrosive gases for a long time to avoid damage to the headlamp;
7. Non-professionals do not disassemble, to prevent damage to the circuit board structure.
8. Note: This product is shipped without batteries and chargers
Specification:
| Package Weight |
|
Shop Before It Ends
Prend fin Sunday, April 14, 2024 at 11:59 AM CAT
Shop Before It Ends
Our Story, Our Promise
Quality and uniqueness is what we offer.
Frequently Asked Questions
-
We ship worldwide through most available shipping methods to your country
-
Currently payment is through Paypal. You can use your credit and debit cards to make payment.
-
We make delivery within 3-15 days depending on delivery method and destination
-
Yes, we do within 30 days of purchase. However, terms and conditions apply.
